converse Command

For UNIX: If the D3 process is not connected to the virtual machine, then converse is not allowed, even if the where command with a z option displays the port as being available.

For Windows: Supports the converse command when the D3 process is connected to the virtual machine and when it is not connected. The port must be connected but not logged on.

The converse BASIC program links the current process to a device. The target or slave device is put into a pass-through mode, allowing data in and out in raw mode.

The converse command stores the PIB number of the port being conversed to in attribute 17 of the dm,pibs file. This information helps track down the converse ports that have been logged off.

Syntax

converse port.number {(options}

The target device (the one being linked to the current device) must be available on the given the port number. It cannot be already attached or linked to another process.

A hot key, or termination, sequence disconnects the link. The default hot key sequence is pressing ESC, followed by X. The default can be modified by using the d option.

If the termination sequence contains an escape, as in the default, an esc-data command is issued automatically, so the process does not get locked out from being able to suspend converse.

When the device is successfully attached, line attached displays on the master terminal, unless the (s option is used.

WARNING

Pressing BREAK on the master terminal, sends a break to the slave port.

 

NOTE

This feature only works for processes connected to a COM port (serial line).

Parameter(s)

options

c

Captures all output on the (slave) screen and writes it to an item in the dm,cap-file file, using the item-ID * n, where n is the current port number.

 

d/hexnum{, hexnum ...}

Designates the sequence of characters to terminate converse mode.

  • Each character is provided in its hexadecimal equivalent of its ASCII value.

  • Each character is separated by a , (comma).

NOTE—A / is required after the d option and before the first hexadecimal number. For example, d/41,42,43,44, indicates that an "ABCD" disconnects the link.

i

Same as the c option, except that output from the master process is captured.

n

Suppresses capturing on converse mode. This is the default.

s

Suppresses the message when the process terminates.

x

Terminates converse mode on target device number and returns target device to logon.

z

Used in conjunction with i or c, translate the nonprintable characters into a period, the carriage returns into an attribute mark, and suppresses the line feeds. Without this option, if a character x'ff' is captured, the item is truncated.

 

NOTE

If the termination sequence contains an escape character (X is the default), it is not easy to send an escape by itself to the target port. This is due to the fact that, since an escape starts the termination sequence, the system waits for the second character. If a character other than X is typed, then escape and the character are sent together. This can create some unexpected results. If an escape is to be used as a regular character, it is preferable to define a less used character for the termination sequence, such as the DELETE key.

Unlike some other implementations, a break is not generated by a special escape character sequence. Press BREAK on the master terminal to send a break signal to the slave device. If the slave device is not a serial line, the break is interpreted accordingly. For instance, if the target is a telnet entity, the break generates the appropriate telnet message.

When capturing is in effect, the data is not stored in real time to the dm,cap-file item. There may be a delay of a few seconds. This is done to reduce the number of file accesses in case of heavy traffic.

Example(s)

Attaches the current process to port 16.

converse 16

Attaches the current process to port 33, capturing screen output from the slave process.

converse 33 (c

Attaches to port 3 and sets the hot key sequence to *++.

converse 3 (d/2a,2b,2b

Attaches to port 42 and captures the screen output from the master process, making sure all data is displayed.

converse 42 (iz

Terminates converse on port 42 and returns port to the logon prompt.

converse 42 (x

See Also

:reset-async Command, cap-file File, dev-att Command, dev-det Command, devs File, link-pibdev Command, mirror Command, Port Number, System Privileges, tandem Command, unlink-pibdev Command