ovf-monitor Command

The ovf-monitor command monitors and displays overflow consumption on a port by port basis.

Syntax

ovf-monitor {*|port{,port}{-port}...} {(options}

Parameter(s)

*

Monitors all ports. This is the default.

port{,port}{-port}...}

Specifies the port(s) or range of ports to monitor.

options

a

Displays all target ports. By default, only the ports that are actively consuming overflow are displayed.

s

Enables scroll mode. Each  new occurrence of activity is displayed as a new line in the output display. Note that older entries will scroll of the screen when the screen becomes full.

tn

Specifies the time in n seconds between refreshes of the displayed ports. The default is 10 seconds.

Upon running ovf-monitor, a set of options display at the bottom of the results:

Press 8=up; 2=down;7=home;1=end;9-PgUp;3=PgDn;ESC=Exit;Rtn=Refresh

The options allow you to move up and down through the displayed results (not available when scrolling mode is enabled), refresh the displayed results or exit the program.

Example(s)

The example below illustrates using the ovf-monitor command to display all target pibs.

:ovf-monitor (a

Overflow Monitor

 

17:25:53

Port

Ovf used

Change

Cached

Change

Cache Max Ports'

Total

0

0

0

No cache

 

 

1838

1

57

0

14

0

30

1838

2

0

0

No cache

 

 

1838

3

45

0

15

0

30

1838

4

0

0

0

0

0

1838

5

0

0

0

0

0

1838

6

0

0

0

0

0

1838

7

0

0

0

0

0

1838

8

0

0

0

0

0

1838

9

0

0

0

0

0

1838

10

0

0

0

0

0

1838

11

0

0

0

0

0

1838

12

0

0

0

0

0

1838

13

0

0

0

0

0

1838

14

0

0

0

0

0

1838

15

0

0

0

0

0

1838

16

17

0

0

0

0

1838

17

823

0

0

0

0

1838

18

822

0

0

0

0

1838

Press 8=up; 2=down;7=home;1=end;9-PgUp;3=PgDn;ESC=Exit;Rtn=Refresh

The example below illustrates setting the ovf-monitor command to use a scrolling display that refreshes every 2 seconds. In this case, only the activity on port 20 is being monitored.

:ovf-monitor 20 (st2

Overflow Monitor

 

17:29:53

Port

Ovf used

Change

Cached

Change

Cache Max Ports'

Total

20

23

23

3

3

30

1860

20

40

17

19

16

30

1877

20

0

-40

19

0

30

1837

20

0

-40

19

0

30

1837

20

0

-40

19

0

30

1837

20

0

-40

19

0

30

1837

20

0

-40

19

0

30

1837

20

0

-40

19

0

30

1837

20

1

0

0

-19

0

1838

20

0

0

0

-19

0

1837

20

0

0

0

-19

0

1837

20

0

0

0

-19

0

1837

20

0

0

0

-19

0

1837

20

0

0

0

-19

0

1837

20

0

0

0

-19

0

1837

20

23

23

3

3

30

1860

Press ESC=Exit;Rtn=Refresh

See Also

init-ovf Command

set-ovf-reserve Command

set-runaway-limit Command

free Command

overflow Command